CG-Hub

metrons · 10-23-2012, 08:18 PM

i setup zbrush how i like it last night, saved UI and custom config. opened zbrush today at work and my UI is missing loads of stuff now (bottom image shows missing items). no idea whats going on? anyone have any clue?

RDeWeese · 11-13-2012, 02:30 AM

Did you hit Ctrl+Shift+I to set your custom user interface as the default to be loaded every time you launch ZBrush?

If you browse to your "Pixologic\ZBrush\ZStartup\UserInterfaceLayout s" folder, do you see your custom UI there?

If your answer to both questions is no, you will need to reconfigure your UI and save it again.

This may be helpful: http://www.pixologic.com/docs/index....terface_Layout. Pay special attention to the last 2 lines at the very bottom of the page.

WilbertPierce · 12-23-2012, 08:16 AM

I've had that problem myself specifically with regards to Mesh information like counts and totals. The only thing I haven't tried but think might fix this is if you bind the missing to a custom palette then bind the palette instead of each individual item.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Custom AK-47	Polygoblin	3D Finished Work	0	09-23-2011 04:31 AM
Saving Format?	RionaWolfheart	Art Discussion	4	09-07-2010 03:50 PM
3D Jam 3#: Saving Beauty - phrenzy84	phrenzy84	3D Jams Archive	9	12-02-2009 01:13 AM
Custom Guitar WIP	Shadow106	3D WIP	18	05-22-2009 09:13 AM
Custom Chopper	Hoobleedyhooblah	3D WIP	0	12-31-2008 02:31 PM

CG-Hub

Members login

General

Challenges

2D Corner

3D Corner

Custom UI not saving correctly? can anyone help me with this?

Site Map

	Permalink #1
metrons Join Date: Jun 2012 Posts: 5 Junior Member Thanks: 0 Thanked 0 Times in 0 Posts	Custom UI not saving correctly? can anyone help me with this? 10-23-2012, 08:18 PM i setup zbrush how i like it last night, saved UI and custom config. opened zbrush today at work and my UI is missing loads of stuff now (bottom image shows missing items). no idea whats going on? anyone have any clue? Attached Thumbnails

	Permalink #2
RDeWeese Join Date: Sep 2012 Posts: 16 Junior Member Thanks: 0 Thanked 2 Times in 2 Posts	11-13-2012, 02:30 AM Did you hit Ctrl+Shift+I to set your custom user interface as the default to be loaded every time you launch ZBrush? If you browse to your "Pixologic\ZBrush\ZStartup\UserInterfaceLayout s" folder, do you see your custom UI there? If your answer to both questions is no, you will need to reconfigure your UI and save it again. This may be helpful: http://www.pixologic.com/docs/index....terface_Layout. Pay special attention to the last 2 lines at the very bottom of the page.

	Permalink #3
WilbertPierce Join Date: Dec 2012 Posts: 8 Junior Member My Mood: Thanks: 0 Thanked 0 Times in 0 Posts	12-23-2012, 08:16 AM I've had that problem myself specifically with regards to Mesh information like counts and totals. The only thing I haven't tried but think might fix this is if you bind the missing to a custom palette then bind the palette instead of each individual item.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)