CG-Hub

damageINC · 10:34 AM

Just finished the base high rez version of a Bertie Mk2 Dirty Deeds variant. I need to make the belt and weapons tonight and tomorrow, then this weekend will be making the low rez bake mesh. Peace.

damageINC · 04-21-2012, 08:29 AM

A couple more updates.....stayed up late last night and finished the pistol. So a couple shots with that. I'm about to start on the machete....as long as I can find some decent ref, should be about 5 times faster than the revolver. Enjoy.

damageINC · 04-21-2012, 10:54 AM

One more before I hit the sack. Machete is done....altered the tip slightly but I like this profile better. Looks meaner and less like a tacky pirate's sword. Gotta do the belt/grenades and a quick sculpt then it's low rez time and textures.

damageINC · 04-23-2012, 10:10 AM

Forgot it was my wedding anniversary this weekend so I didn't get as much done as I had hoped. BUT......did finish the high res model. So tomorrow I'll do a quick sculpt on Bertie and immediately begin baking down the low poly. Have a good night.

damageINC · 05-02-2012, 11:11 AM

Been a bit.....had a lot of trial and error getting the normal maps to bake right. At any rate, started texturing today. This is an update from Marmoset. About 30% done with textures. Does anyone know why there is texture jumping from mesh to mesh in Marmoset when spinning the model? Vexing.....oh and, with the weapons and belt, it weighs in at just over 14k tri's. The character alone is around 11k.

damageINC · 01:53 AM

Next to last update before I call this guy done. Still need to do a second pass on rust and grime, then give the utility belt some love and finish with a proper set of spec maps and I'mma done. Hope you like it.....feel free to crit it.

LSheridan · 05-05-2012, 02:59 PM

Awesome - I love the small painted on details.

damageINC · 05-06-2012, 03:42 AM

Thanks man, very much appreciated. Just posted the final rendering of this guy in my gallery! : )

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
dirty car	brijeshA	3D WIP	0	09-20-2011 03:44 PM
Mohagen - Webcomic - Something Fresh in the Dirty Water	kipling00	Sequential Art & Storyboarding	0	02-16-2011 03:23 PM
Dirty C. Some sketches..	dirtyc	Sketchbooks	5	03-08-2010 02:29 PM

CG-Hub

Members login

General

Challenges

2D Corner

3D Corner

Dirty Bertie

Site Map

	Permalink #1
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	Dirty Bertie 04-19-2012, 10:02 PM Just finished the base high rez version of a Bertie Mk2 Dirty Deeds variant. I need to make the belt and weapons tonight and tomorrow, then this weekend will be making the low rez bake mesh. Peace. Attached Thumbnails Last edited by damageINC; 05-03-2012 at 10:34 AM.

	Permalink #2
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	04-21-2012, 08:29 AM A couple more updates.....stayed up late last night and finished the pistol. So a couple shots with that. I'm about to start on the machete....as long as I can find some decent ref, should be about 5 times faster than the revolver. Enjoy.

	Permalink #3
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	04-21-2012, 10:54 AM One more before I hit the sack. Machete is done....altered the tip slightly but I like this profile better. Looks meaner and less like a tacky pirate's sword. Gotta do the belt/grenades and a quick sculpt then it's low rez time and textures.

	Permalink #4
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	04-23-2012, 10:10 AM Forgot it was my wedding anniversary this weekend so I didn't get as much done as I had hoped. BUT......did finish the high res model. So tomorrow I'll do a quick sculpt on Bertie and immediately begin baking down the low poly. Have a good night.

	Permalink #5
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	05-02-2012, 11:11 AM Been a bit.....had a lot of trial and error getting the normal maps to bake right. At any rate, started texturing today. This is an update from Marmoset. About 30% done with textures. Does anyone know why there is texture jumping from mesh to mesh in Marmoset when spinning the model? Vexing.....oh and, with the weapons and belt, it weighs in at just over 14k tri's. The character alone is around 11k.

	Permalink #6
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	05-05-2012, 01:50 AM Next to last update before I call this guy done. Still need to do a second pass on rust and grime, then give the utility belt some love and finish with a proper set of spec maps and I'mma done. Hope you like it.....feel free to crit it. Last edited by damageINC; 05-05-2012 at 01:53 AM.

	Permalink #7
LSheridan Join Date: Jan 2012 Posts: 4 Junior Member Thanks: 0 Thanked 2 Times in 2 Posts	05-05-2012, 02:59 PM Awesome - I love the small painted on details.

The Following User Says Thank You to LSheridan For This Useful Post:
damageINC

	Permalink #8
damageINC Join Date: May 2011 Posts: 45 Member Thanks: 2 Thanked 2 Times in 2 Posts	05-06-2012, 03:42 AM Thanks man, very much appreciated. Just posted the final rendering of this guy in my gallery! : )

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)